LG Monitor “No Signal Entering Power Saving Mode Shortly” Error (5 FIXES)

Charles Nelson
By Charles Nelson 27 Min Read
27 Min Read
fix lg monitor no signal entering power saving mode shortly error featured


LG Monitors often face an error displaying “No Signal Entering Power Saving Mode Shortly”. To help you out, here are five simple fixes to resolve the issue. First, ensure that all cables are correctly connected and secure. Second, check if your monitor’s input source is correct. Third, update your display drivers to the latest version. Fourth, perform a power reset by disconnecting all cables and waiting for a few minutes before reconnecting them. Finally, try replacing your monitor’s video cable.

It is important to note that outdated display drivers can also contribute to this error. According to LG’s official website, you can find and download the latest driver updates for your monitor using their support page.

Overall, with these easy-to-follow fixes, you can quickly resolve the problem of “No Signal Entering Power Saving Mode Shortly” error on your LG Monitor. Why wait for a signal when you can just embrace the power-saving lifestyle?

Causes of “No Signal Entering Power Saving Mode Shortly” Error

The Error of “No Signal Entering Power Saving Mode Shortly” on LG Monitor can be caused by several factors. It may be due to a faulty graphics card, poor display settings, an outdated monitor driver, or a problematic power source. Another common cause is the monitor’s sleep mode or power-saving setting that automatically turns off the monitor when idle. To fix this error, you may need to troubleshoot your computer settings, update drivers, check the power source, or adjust the monitor’s sleep mode settings appropriately.

If none of the above troubleshooting techniques resolve the issue, you can reach out to LG’s customer support for further assistance. It is essential to address this problem promptly as it can lead to data loss, productivity disruption, and even hardware damage due to overheating. Don’t let this error prevent you from using your LG monitor efficiently. Seek help to get it fixed as soon as possible.

Don’t wait until the problem worsens. Act immediately to prevent missing out on essential tasks that require your monitor’s attention. Get help from experts or other technical resources available to you to avoid this error and enjoy uninterrupted monitor usage.

Don’t blame the monitor, it’s not playing hard to get – just tighten those loose cables!

Disconnected or Loose Cables

This section of the article covers the issue of cables not being properly connected. Ensuring all cords are appropriately plugged in is crucial to avoid the “No Signal Entering Power Saving Mode Shortly” Error.

  • Check all cables for damage or defects
  • Tighten all connections securely
  • Ensure cables are firmly seated in their ports
  • Avoid kinking or twisting cables
  • Replace any damaged or worn-out cables immediately

It is important to regularly check for loose or disconnected cables, as these issues can lead to other malfunctions in the system. Taking care of cable management can extend the lifespan of your hardware, ensuring optimal performance.

According to experts at PCMag, poorly maintained and connected cables are one of the leading causes of computer hardware failures.

The only time ‘Wrong Input or Output Source‘ is a valid excuse is when your ex tries to blame the relationship’s failure on you.

Wrong Input or Output Source

Misconfigured display source may lead to ‘No Signal Entering Power Saving Mode Shortly’ error. Make sure the output port on your computer matches the input port of your monitor and the correct video settings are set. This will ensure the computer and display have a synchronized connection.

Additionally, if using multiple inputs or displaying multiple sources, verify that the correct input source is selected on your monitor. Avoid delay while switching between inputs by disabling unused ones.

Pro Tip: For different types of computer hardware, refer to manufacturer’s instructions for specifics on input/output matching.

Why settle for a supported resolution when you can live dangerously with an unsupported one? No signal? More like no fear.

Unsupported Resolution or Refresh Rate

When your monitor displays the message “No Signal Entering Power Saving Mode Shortly“, it could be due to an issue with an Unsupported Resolution or Refresh Rate. This means that your computer or graphics card is trying to display a resolution or refresh rate that your monitor does not support.

To better understand this, we can create a table with two columns: Resolution and Refresh Rate. Under Resolution, we have options such as 1024×768, 1280×720, and 1920×1080. The Refresh Rates include 60Hz, 75Hz, and 144Hz. If your computer tries to display a resolution or refresh rate that is not supported by your monitor, it will cause the error message to occur.

It’s important to note that unusual resolutions or refresh rates may be unsupported by older monitors. So if you’re using an outdated monitor, it’s likely that it won’t support some of the latest resolutions and refresh rates.

If you continue to experience this issue even after changing the resolution or adjust the refresh rate, it may be worth considering upgrading your monitor to a newer model with greater compatibility.

If your graphics card were a person, it would be the unreliable friend who always cancels plans last minute.

Faulty Graphics Card or Driver

An issue that often leads to the “No Signal Entering Power Saving Mode Shortly” message on your monitor is caused by a broken graphics card or driver. When there’s an error within the graphics unit, it cannot communicate with the computer or display properly. This problem causes the monitor to switch on and go black after a while, leading to power-saving mode. In such cases, reinstalling drivers or updating them may fix the issue.

READ ALSO:  How to Archive Reels on Instagram? : Hide Reels (2023)

It’s important to note that outdated, damaged, or incompatible drivers are culprits for this error in most cases. An insufficient power supply can also cause this issue as it restricts certain features of a graphics card from functioning appropriately.

If you don’t have any idea what caused this error, check your cables and ports before attempting any corrective measures. A loose connection can also cause this problem because hardware needs enough functioning space for effective operations.

A user reported having experienced this problem when their system went into hibernation while running CPU-intensive programs. Even escalating the cooling level failed to solve the issue until they updated their drivers.

If your monitor is as defective as your love life, or your power saving settings are as flawed as your decision-making skills, then it’s no wonder you’re facing the ‘No Signal Entering Power Saving Mode Shortly’ error.

Defective Monitor or Power Saving Settings

A likely cause for the error, where the monitor fails to receive a signal and enters power-saving mode soon after, may be due to malfunctioning hardware components of the display unit or issues with the settings related to power consumption—a possible indication of defective hardware or misconfigured settings. Such an occurrence may manifest after either regular use or during attempts to change monitor settings. Checking for physical damage or replacing faulty parts might resolve this otherwise troublesome issue.

Furthermore, if adjusting the power plan settings in Windows does not help restore the monitor, it is important to verify that the cable connection between your system’s display port and the monitor is firm. Unsecured cables could disrupt connectivity resulting in an unstable output.

Many manufacturers offer helpful customer support services when it comes to resolving such errors that might result from running different configurations on their products. It is advisable to check with their support team to get insights on how best to troubleshoot this issue.

According to PC Magazine, one out of ten monitors experience out-of-the-box faults each year, making it obvious that malfunctions are a pervasive challenge for new products too and require careful evaluation before dispensing them into general use.

I guess the solution isn’t just to yell at the computer screen to wake up from its power nap.

Solutions for “No Signal Entering Power Saving Mode Shortly” Error

In this article, you will discover effective ways to troubleshoot the issue of a “No Signal Entering Power Saving Mode Shortly” error on your LG monitor. Follow the simple steps below to fix the issue and get your monitor up and running smoothly.

  1. Check the Power Source: Ensure your monitor is properly plugged in and turned on. Make sure the power cable is firmly seated in the power socket of your monitor.
  2. Check the Display Connections: Check the cable that connects your monitor to your computer. Ensure that the connectors are correctly seated and free of dirt or debris.
  3. Update your Graphics Card Driver: Outdated graphics card drivers can sometimes cause display issues. Check for the latest drivers for your graphics card and install them.
  4. Reset Your Monitor: If all else fails, factory reset your monitor. Locate the “Reset” button on the monitor’s control panel, or check the owner’s manual for instructions.
  5. Contact LG Support: If you have tried all of the above and the issue persists, contact LG customer support for further assistance.

It is essential to note that this problem may occur due to various reasons, ranging from driver issues to hardware failures. However, following the steps above should resolve the issue in most cases.

If you have gone through all the solutions and still face the issue, reach out to a professional for further assistance.

Make sure your cables are plugged in snug, because disconnection is not the optimal path to enlightenment.

Check and Reconnect Cables

The first step to resolving the issue of the display monitor showing “No Signal Entering Power Saving Mode” is to confirm and establish a proper connection. The following steps should be followed in sequence for better understanding:

  1. Check all cables for proper connectivity
  2. Ensure that all cable connections are tightly fit
  3. Inspect for damaged or frayed cables affecting signal strength
  4. Try swapping and changing wires to establish any malfunctioning in the cables
  5. Determine whether the correct port is being used for the display device based on your computer system’s compatibility.
  6. If using an adapter, make sure it is working correctly.

It is also essential to ensure that the power supply is appropriate for both devices and check if there are any loose power supply connections.

In case you are still facing an issue despite checking and reconnecting all cables, try restarting your device. If the problem persists, please consult with a certified technician or reach out to customer service.

Don’t wait until it’s too late – double-check and reconnect your cables now to avoid missing out on critical work or entertainment!

Don’t be a fool, select the right input source and you won’t end up in power-saving mode purgatory!

Select Correct Input or Output Source

To resolve the issue of the screen displaying “No Signal Entering Power Saving Mode Shortly,” you need to ensure that the correct input or output source is selected.

Here’s a table displaying columns for selecting the correct input or output source:

Input Source Output Source
HDMI 2 Monitor
VGA Projector

Ensure that you choose the appropriate input and output sources on your device settings to match with the cable or device that is connected.

It’s crucial to follow this step accurately, as choosing an incorrect source may lead to display problems. Re-selecting a wrong source can reset it to its default value. Ensure you check all available sources before doing any operations.

READ ALSO:  Generate Mint Mobile Account Number And PIN In Minutes

This situation happens because of an incorrect sequence of selecting sources and connecting cables, leading to displaying mistakes.

Who knew all it took was a game of resolution roulette to solve the dreaded ‘No Signal’ error?

Adjust Resolution or Refresh Rate

To resolve the error of a monitor showing “No Signal Entering Power Saving Mode Shortly,” one can adjust the display’s resolution or refresh rate. This simple solution requires only a few easy steps to complete.

  1. First, right-click on your computer’s desktop and select “Display settings.”
  2. Next, discover the option for “Advanced display settings,” and click it.
  3. Finally, you’ll be able to modify the display’s resolution and/or refresh rate here to correct the error.

It’s critical to remark that this solution differs slightly depending on your operating system and monitor version, so it’s always a good idea to refer to your monitor user manual or contact their customer service for more information if you’re unsure of how to proceed.

This error is typical when a screen’s power-saving mode is enabled, which may happen when the PC fails to transmit data correctly over HDMI or VGA cables. Fortunately, this issue can be remedied by adjusting the resolution or refresh rate. By doing so, an uninterrupted signal will be sent between PC and monitor, allowing for an uninterrupted visual experience.

If your graphics card was a person, updating them would be the equivalent of giving them a much-needed facelift.

Update Graphics Card or Driver

Keeping your graphics card or driver updated is essential to avoid the “No Signal Entering Power Saving Mode Shortly” error. Keep your hardware optimal by installing the latest version of graphics driver as it fixates performance bugs and improves overall system functioning.

Make sure you are aware of the exact graphics card installed in your system, before downloading or installing any update or even troubleshooting this error. Sometimes updating drivers may not solve the problem. In that case, you can reinstall the entire system.

For an upgraded experience, download automatic graphic card drivers\’ software which detects all models and installs appropriate drivers without requiring user interference.

Pro Tip: If none of these methods work, check if your computer has a faulty power supply unit that causes this problem. If considered necessary, seek help from a professional technician for installation and maintenance standards.

Don’t let your computer fall asleep on the job – disable or adjust those pesky power saving settings.

Disable or Adjust Power Saving Settings

To fix the issue of ‘No Signal Entering Power Saving Mode Shortly’, you may want to customize your power settings. Here’s how you can ‘Personalize or Modify Power saving preferences’:

  1. Start by looking for the power options within the Control Panel or the settings menu.
  2. Check if there are presets, such as “balanced” or “power saver,” that might be causing problems for your system.
  3. Customize the settings by disabling any unnecessary processes or lowering screen brightness to save energy consumption.
  4. Restart your computer and check if these modifications fixed the problem.

It is crucial to ensure that your device’s power settings align with its hardware capabilities. Misconfigured power-saving features can lead to various technical issues. By customizing your device’s energy usage, you can avoid critical performance problems in the future.

Your computer, in general, will consume less electricity while on standby than when it is fully active. However, keeping a monitor on sleep mode will not significantly decrease its overall energy consumption. Instead, consider powering off all devices when they are not in use to reduce electricity bills.

In a real-world scenario, many users have reported encountering similar issues with their monitors due to misconfigured power-saving modes. They customized their energy usage preference and solved this problem.

Time to bring out the big guns – let’s troubleshoot this error like our internet connection depends on it.

Additional Troubleshooting for “No Signal Entering Power Saving Mode Shortly” Error

If your LG monitor shows a “No Signal Entering Power Saving Mode Shortly” error, you can try some additional troubleshooting steps to resolve the issue. Follow these four steps:

  1. Check all connections: Ensure the monitor cable is properly connected to the computer and both devices are on. If using a VGA cable, make sure the pins are clean and straight. Try a different cable or port if possible.
  2. Reset monitor settings: Press the Menu button on the monitor and navigate to the Reset option. Select it and confirm the reset. Check if the error persists.
  3. Update or reinstall graphics driver: Go to the device manager in the computer, find the graphics card or adapter, right-click it and choose Update driver. Alternatively, uninstall the driver and restart the computer to automatically reinstall it.
  4. Test monitor on another computer: Connect the monitor to a different computer or laptop and see if it works without issues. If it still shows the error, it may indicate a hardware problem.

If none of these steps solve the “No Signal Entering Power Saving Mode Shortly” error, you can try contacting LG customer support or a technician for further assistance. However, note that some older LG monitors may not be compatible with newer graphics cards or operating systems, so they may require a firmware update or replacement.

It is important to diagnose and fix monitor errors promptly to avoid damage to the device or loss of productivity. Some users have reported that the “No Signal Entering Power Saving Mode Shortly” error can also occur due to a faulty power supply or capacitors in the monitor, but these issues are more rare and complex to fix.

In some cases, users have also reported experiencing this error after upgrading or changing their computer hardware or software. Therefore, it is advisable to check for compatibility issues and update all drivers and settings accordingly before connecting the monitor.

Time to hit the reset button on your monitor, just like you do on your life every Monday morning.

Reset Monitor Settings

To fix the error of “No Signal Entering Power Saving Mode Shortly,” resetting the monitor settings is a practical solution.

READ ALSO:  The Ultimate Guide to A Perfect Stacked Monitor Setup

Here is a 4-step guide to help you reset monitor settings:

  1. Turn off your monitor and unplug it from the power source.
  2. Pull out all cables connected to the monitor.
  3. Press and hold down the power button on your monitor for 10-15 seconds. This will drain any residual power left in the system.
  4. Plug back in all cables, connect to power, and turn on your monitor.

In addition to these steps, make sure that your computer’s graphics card drivers are up to date.

It’s worth knowing that some monitors allow you to reset their settings through an on-screen menu rather than physical buttons. Refer to your device’s manual or online instructions for more details.

According to PCMag, a common cause of this issue can be outdated or corrupt graphics drivers.

Let’s hope the monitor finds a more compatible partner on the next system test.

Test Monitor on Another System

To determine if the monitor issue is due to a problem with your computer or the monitor itself, testing the monitor on another system is a recommended step.

  1. Disconnect all cables and accessories connected to the current system.
  2. Carefully remove the monitor and reconnect it to another system using a different set of cables.
  3. Turn on both systems and wait for the new system to boot up.
  4. If you see an image on the screen, this indicates that there might be an issue with your original computer or its graphics card. However, if you cannot detect any picture, this indicates that there might be an issue with the monitor hardware.
  5. To diagnose further, try connecting your computer to another display by following ‘Connecting Another Display’.

It is important to note that performing this test helps isolate any hardware issues in either the monitor or computer.

Now that you have tested your monitor on another system, it’s time to connect your computer to another display. This will help ascertain if there are any issues with the graphics card of your PC.

Unfortunately, sometimes even Google can’t solve our tech problems, and it’s time to call in the IT cavalry.

Next Heading: Check Your Connections.

Seek Professional Help

It is recommended to consult a certified technician for assistance in resolving the “No Signal Entering Power Saving Mode Shortly” error. Trained professionals have the necessary knowledge and skills to diagnose and fix hardware or software issues that may be causing this problem.

They can perform advanced troubleshooting techniques and utilize specialized equipment to identify the underlying issue. The cost of hiring a professional may vary depending on the complexity of the problem, but it can save time, effort, and money in the long run by preventing potential damage to your device.

In addition, seeking help from reliable sources such as authorized service centers or approved repair shops can ensure that only genuine parts are used for repairs, minimizing any possible risks associated with third-party replacements.

According to The Verge, unauthorized repairs performed outside of an authorized service center could potentially void your warranty and leave you vulnerable to safety risks.

Therefore, it is crucial to do proper research and select a trustworthy technician or service provider when seeking professional help for resolving tech-related problems.

Congratulations! You’ve successfully conquered the ‘No Signal Entering Power Saving Mode Shortly’ error, but if your computer starts making strange beeping noises, it’s time to run.


The LG monitor ‘No Signal Entering Power Saving Mode Shortly‘ error can be fixed by following simple steps. First, check the cables and connections to ensure they are properly connected. Second, restart your computer and monitor. Third, adjust the display settings on your computer. Fourth, update your graphics card driver. Finally, reset your monitor to its default settings.

It is important to address this issue promptly as it can lead to prolonged downtime and decreased productivity in work environments.

According to TechRadar, LG is one of the leading manufacturers of computer monitors with a wide range of models available for different purposes.

Frequently Asked Questions

What does the "No Signal Entering Power Saving Mode Shortly" error mean on my LG monitor?

This error typically means that your monitor is not receiving a signal from your computer or other device connected to it, and is entering power saving mode as a result.

How can I fix the "No Signal Entering Power Saving Mode Shortly" error on my LG monitor?

There are several potential solutions you can try, including checking your cables and connections, resetting your monitor, updating your graphics driver, resetting your BIOS settings, and checking your hardware for any issues.

Why does the "No Signal Entering Power Saving Mode Shortly" error only occur on my LG monitor, and not others?

This error can occur on any type of monitor or display, but may be more common on LG monitors due to their specific hardware and software configurations.

How do I check my cables and connections to fix the "No Signal Entering Power Saving Mode Shortly" error on my LG monitor?

You can check your monitor's cables and connections by unplugging and re-plugging them, making sure they are attached correctly and securely. You can also try using different cables or ports to see if that resolves the issue.

How do I reset my LG monitor to fix the "No Signal Entering Power Saving Mode Shortly" error?

To reset your monitor, first unplug it from the power source and wait for at least 30 seconds. Then, plug it back in and turn it on again. You can also try resetting your monitor to its factory settings through the on-screen menu.

What should I do if none of these solutions work to fix the "No Signal Entering Power Saving Mode Shortly" error on my LG monitor?

If none of these fixes work, there may be an issue with your hardware that requires professional repair or replacement. Contact LG customer support or a certified technician for assistance.

Share This Article
Hello, I'm Charles, a tech blog author passionate about all things tech. I got into writing because I wanted to combine my love for technology with my copywriting skills. I've been writing for over seven years, continuously learning and adapting to the ever-evolving tech landscape. My deep interest in technology naturally led me to delve into blogging and digital marketing, allowing me to share my knowledge and insights with a wider audience. Join me as we explore the exciting world of tech together!
Leave a comment

Leave a Reply

Your email address will not be published. Required fields are marked *